Field NotesComparisonsNo. 03
Capacitive vs. resistive soil moisture sensors: what’s the difference?
Both kinds of probe give you a number. Whether that number tracks water or salt is the difference that matters.

The short answer A resistive sensor passes a current between two bare metal probes and reads how easily it flows, so salts, fertilizer and temperature shift the reading, and the probes corrode. A capacitive sensor reads the soil’s dielectric permittivity through coated electrodes, which tracks water more directly and lasts longer, though air gaps, soil type and high salinity still affect it. Either type needs calibrating to your mix to give real numbers.
Push a cheap moisture probe into a pot and you get a number. What that number tracks depends on how the probe senses: by conductivity or by permittivity. The two fail in different ways.
How a resistive sensor works
A resistive sensor has two exposed metal electrodes. It sends a small current from one to the other through the soil and measures how much the soil resists it. Wetter soil conducts better, so resistance falls as moisture rises.
The catch is what carries the current. Water itself is a poor conductor; as soil-sensor manufacturer METER Group explains, the dissolved ions in the soil water carry the charge. So a resistive probe reads salt as well as water. Three things raise or lower conductivity at the same moisture:
- Salts and fertilizer. Ion concentration largely sets soil electrical conductivity (EC), and synthetic fertilizers add salts, according to USDA NRCS. METER shows that a modest change in salinity can shift a resistive sensor’s calibration more than tenfold.
- Temperature. Soil EC falls about 2.2% for each degree Celsius the soil cools (USDA NRCS), so the same moisture can read drier in a cold room.
- Clay. EC generally rises with clay content (USDA NRCS).
Then there’s wear: bare metal carrying current through wet soil corrodes. In a 2022 lab comparison from IIT Delhi (posted as a preprint), the exposed resistive probes were sensitive to corrosion, and the authors judged them better for quick spot checks than for staying in the soil. METER rates resistance sensors low on both accuracy and durability.
How a capacitive sensor works
A capacitive sensor treats the soil as the dielectric in a capacitor, the insulating layer between two conductors. How much charge that capacitor holds depends on the soil’s dielectric permittivity, and water dominates it. UF/IFAS Extension gives values of about 81 for liquid water, 2 to 5 for soil minerals and 1 for air. Add water and permittivity climbs steeply, so the sensor tracks volumetric water content (volume of water per volume of soil) more directly than conductivity does.
The electrodes don’t need bare contact with the soil. On the low-cost capacitive boards Placidi and colleagues tested in 2020, a solder-resist coating separates the copper electrodes from the soil. In the IIT Delhi comparison, the capacitive probes’ polymer coating resisted electrolysis and oxidation, and the authors rated them suitable for long-duration measurement.
Capacitive sensors still have weak spots:
- Air gaps. METER calls air gaps from poor installation the largest threat to accuracy for capacitance and TDR sensors. With a permittivity of 1, air reads as dry.
- Soil type. Clay activity, especially in smectite clays, ranks second on METER’s list. Placidi’s team found porosity severely affects capacitive readings, so packing density matters.
- Salinity, depending on frequency. At lower measurement frequencies, the sensor polarizes salts along with water; around 50 MHz and above, that influence is reduced (METER). Even so, METER notes capacitance sensors become inaccurate at high salinity, above 8 dS/m in a saturation extract.
- Temperature. UF/IFAS lists capacitance-type sensors as more sensitive than TDR to temperature, bulk density, clay content and air gaps.
Accuracy and calibration
Low-cost sensors typically output a voltage, not water content; converting it takes a calibration curve for your soil or mix, and how to calibrate a soil moisture sensor walks through making one.
Once calibrated, the gap between the two types is real:
- METER rates capacitance and TDR sensors accurate to about 2 to 3% with soil-specific calibration, and resistance sensors as low accuracy.
- UF/IFAS puts capacitance-type sensors at ±0.01 ft³/ft³ after soil-specific calibration, which is about 1 percentage point of water content.
- In a 2020 lab study in Sensors, Adla and colleagues calibrated four inexpensive sensors to each soil. The capacitive ones (roughly a tenth the price of a TDR sensor) averaged a mean absolute error of 1.90% water content. The very low-cost resistive ones averaged 3.82%, about twice as much. Soil-specific calibration improved every sensor substantially, and the authors recommend frequent recalibration for resistive sensors because salt levels vary.
Why cheap meters read differently
Two probes in the same pot can disagree. The usual reasons:
- They measure different things. A resistive meter reads conductivity, so a pot you just fertilized can read wetter than an unfertilized pot at the same moisture.
- No calibration for your mix. Potting mixes vary in texture and porosity, and both shift the reading.
- Unit-to-unit variation. Placidi’s team found two sensors of the same low-cost model differed by more than 5%, though each was consistent with itself.
- A small sensing zone. A resistive probe senses only the soil between its two electrodes (METER), and UF/IFAS puts the sphere of influence of capacitance sensors at about 1.6 inches. One reading describes one pocket of the pot.
- Poor contact. Air gaps around a wiggled or loosely seated probe read as dry.
- Temperature and wear. Soil temperature shifts conductivity, and corrosion degrades resistive probes with use.
Capacitive vs. resistive at a glance
| Resistive | Capacitive | |
|---|---|---|
| What it senses | Electrical conductivity between two bare electrodes | Dielectric permittivity, through coated electrodes |
| Effect of salts and fertilizer | Strong | Small, except at high salinity; larger at low frequencies |
| Effect of temperature | Yes (soil EC changes about 2.2% per °C) | Yes, more than TDR |
| Electrode corrosion | Yes | Coating resists it |
| Error after soil-specific calibration (one lab study) | 3.82% average | 1.90% average |
| Durability (METER) | Low | High |
| Relative price (METER) | Lowest | Low to moderate |
| Best use | Quick spot checks, then pull it out | Left in place to track changes over time |
Other types you’ll see mentioned
- Tensiometers measure how tightly the soil holds water (suction, or matric potential), not how much water is there. UF/IFAS gives a typical range of 0 to 0.80 bar. Salinity doesn’t affect them, because salts move freely through the porous ceramic tip, but they need close contact with the soil.
- TDR (time domain reflectometry) times an electrical pulse traveling along metal rods. UF/IFAS calls it relatively insensitive to salinity as long as a usable pulse comes back, and accurate to about ±0.01 ft³/ft³, with a small sensing zone about 1.2 inches around the rods. METER rates its price moderate to high.
- FDR (frequency domain reflectometry) is a capacitance method that sweeps an oscillator’s frequency to find the soil’s resonant frequency.
- Gypsum and granular matrix blocks are resistance sensors set in a porous block that buffers salinity. UF/IFAS notes gypsum readings can change up to 3% per °C, and gypsum blocks dissolve and lose calibration over time, especially in saline soil.
How to place and read a probe in a pot
- Aim for the root zone. Insert the probe vertically, about halfway between the stem and the pot wall, deep enough that the whole sensing area is in the mix. Keep any electronics at the top of the probe out of the soil.
- Push once, don’t wiggle. Rocking the probe opens air gaps, and air reads as dry. If it hits resistance, try a new spot. Firm the mix gently around it.
- Read the same spot each time. Each reading covers only a small zone, so in larger pots check two or three spots and compare.
- Pull resistive probes out after reading. Wipe them clean and store them dry. Left in wet soil, the bare electrodes corrode.
- Set your own reference points. Take a reading after a thorough watering once the pot has drained, and another when your usual check (the finger test or the pot’s weight) says it’s time to water. Those two numbers bracket “wet” and “due” for that plant and mix. Our guide to how often to water houseplants covers those checks.
- Re-check after fertilizing or repotting. Fertilizer shifts a resistive reading, and a new mix needs new reference points for either type.
- Watch the trend. Day-to-day change tells you more than any single number. If a pot still reads wet several days after watering, see overwatering vs. underwatering.
Sources
- Soil moisture sensors - How they work. Why some are not research gradeMETER Group
- Field Devices For Monitoring Soil Water ContentUF/IFAS Extension, University of Florida (EDIS BUL343)
- Laboratory Calibration and Performance Evaluation of Low-Cost Capacitive and Very Low-Cost Resistive Soil Moisture SensorsSensors (MDPI), Adla et al., 2020
- Characterization of Low-Cost Capacitive Soil Moisture Sensors for IoT NetworksSensors (MDPI), Placidi et al., 2020
- Soil Electrical ConductivityUSDA Natural Resources Conservation Service (Soil Quality Indicators)
- Comparative Analysis and Calibration of Low Cost Resistive and Capacitive Soil Moisture SensorChowdhury, Sen and Janardhanan, IIT Delhi (arXiv preprint 2210.03019)
General information, not professional advice for a specific plant or crop. Spot something wrong? Email info@terrathink.io.


