Field NotesPlant techNo. 07

What do soil moisture readings mean? Volumetric water content, explained

A volumetric moisture reading is the share of the soil’s volume that is water. Whether that is wet or dry depends on the soil, the pot and how tightly the water is held.

Soil samples settling in test tubes in a rack on tilled soil

The short answer Volumetric water content (VWC) is the volume of water in a soil sample divided by the sample’s total volume, so 0.20 m³/m³, or 20%, means a fifth of the volume is water. What that means for a plant depends on the soil: 20% is wetter than field capacity in sand, about halfway through the available range in loam and below the wilting point in clay. A meter’s “%” is only VWC if it comes from a VWC calibration, and it is most accurate once calibrated to your soil or mix.

Capacitance and TDR sensors estimate volumetric water content from the soil’s dielectric constant. The number only helps once you know what range it can move through in your soil.

What volumetric water content measures

Volumetric water content, written θ (theta), is the share of a sample’s volume taken up by water:

θ = V_water / V_total

V_water is the volume of water and V_total is the whole sample: solids, water and air. Units are m³/m³ or cm³/cm³, often shown as a percentage. Texas A&M’s irrigation guide E-618 notes that θ is always less than 1.

Oven-dry soil is 0% by definition. Saturation is not 100%. Soil is saturated when its pores are full, and soil sensor maker METER Group puts total pore space at around 50% at a typical bulk density.

Soil labs often measure water by weight instead:

w = m_water / m_dry

w is gravimetric water content (g/g), m_water is the mass of water lost on oven drying and m_dry is the oven-dry mass. The Kansas State soils lab manual stresses dividing by dry weight, not wet. Bulk density converts one to the other:

θ = w × ρb / ρw

ρb is dry bulk density (oven-dry mass divided by total volume, g/cm³) and ρw is the density of water, 1.0 g/cm³.

Worked example: weight to volume

Example. You lift a 100 cm³ core out of a garden loam. It weighs 156 g fresh and 130 g oven-dry, so it lost 26 g of water, which is 26 cm³.

  • Gravimetric: w = 26 / 130 = 0.20 g/g (20% by weight)
  • Bulk density: ρb = 130 / 100 = 1.30 g/cm³
  • Volumetric: θ = 0.20 × 1.30 / 1.0 = 0.26 (26% by volume)

Check: 26 cm³ of water in 100 cm³ of soil is 0.26. Dividing by the wet mass (26 / 156) gives about 17%, the mistake K-State warns about.

Weight-based numbers mislead in potting mix. Bilderback and colleagues (HortTechnology, 2005) give a normal dry bulk density of 0.19 to 0.70 g/cm³ for substrates. At 0.20 g/cm³, a mix at 50% by volume is 250% by weight (0.50 × 1.0 / 0.20 = 2.5 g/g).

Saturation, field capacity and the wilting point

  • Saturation. Every pore is full. E-618 puts the tension of saturated soil at about 0.1 centibar or less. The water above field capacity is gravitational water, which the K-State manual says “drains from macropores too rapidly for plants to use.”
  • Field capacity (FC). E-618 defines it as the water content when drainage after a heavy irrigation changes from fast to slow, which takes 2 to 3 days in loam to clay soils. It is often taken as -33 kPa for fine-textured soils and -10 kPa for sandy soils, which METER calls “crude starting points.” E-618 gives about 30 centibars of tension for loam to clay soils and 10 for sands.
  • Permanent wilting point (PWP). The water content at which plants wilt and can’t recover overnight (E-618). The standard value is -1500 kPa (-15 bar), which METER notes was set experimentally in sunflowers; E-618 says wilting falls between 10 and 20 bars of tension. Soil at the wilting point isn’t dry, but what’s left is held too tightly for roots.

Plant-available water is the difference:

PAW = θ_FC − θ_PWP

θ_FC and θ_PWP are VWC at field capacity and at the permanent wilting point.

On units: 1 bar = 100 kPa = 100 centibars, so 1 cb = 1 kPa. Tensiometers report tension as a positive number: 33 cb of tension is a potential of -33 kPa.

Typical values by soil texture

The first number in each cell is from E-618, which cites Hanson (2000); the number in parentheses is METER’s representative value. All are VWC.

Soil texture Field capacity Wilting point Plant-available water
Sand 10% (5%) 4% (1%) 6% (4%)
Loamy sand 16% (10%) 7% (2%) 9% (8%)
Sandy loam 21% (17%) 9% (6%) 12% (11%)
Loam 27% (27%) 12% (14%) 15% (13%)
Silt loam 30% (27%) 15% (13%) 15% (14%)
Clay loam 29% (36%) 18% (23%) 11% (13%)
Silty clay 40% (40%) 20% (28%) 20% (12%)
Clay 40% (42%) 22% (32%) 18% (10%)

The sources roughly agree on loam and silt loam (within 3 points) and drift apart toward the sandy and clayey ends: METER’s sand holds half as much at field capacity (5% vs. 10%), and its clay far more at the wilting point (32% vs. 22%). Treat any table as a first estimate; METER says real field capacity has to be found from water content data in the field.

Water content vs. water potential

Water content tells you how much water is there, not how hard a root has to pull to get it. That is water potential, and in soil the part that matters most is matric potential. E-618 describes the same pull as soil moisture tension, which it reports as a positive number. Matric potential is near zero in saturated soil and gets more negative as soil dries (tension rises), so roots work harder for the water.

METER’s comparison: like heat, water content “is just an amount,” while -33 kPa is -33 kPa “whether it’s a clay or a sand.” The K-State manual gives the pattern: as clay content rises, soil holds more water at a given potential. At 20% VWC, both sources put sand above field capacity, loam inside its available range and clay below its wilting point. METER’s own example is 32%: field capacity in a sandy clay loam, the wilting point in a clay.

Tensiometers measure the other quantity, reading tension directly through a porous ceramic cup; E-618 calls them the one tension sensor that doesn’t need calibration. Their useful limit is about 80 cb (-80 kPa), past which air can enter the cup and break the suction. That covers field capacity but stops far short of the wilting point.

Container capacity and the perched water table

Container capacity is the water a substrate holds, as a percent of its volume, once it has drained; it plays the role of field capacity. Air space (air-filled porosity) is total porosity minus container capacity.

Bilderback and colleagues, citing Yeager et al. (1997), give these ranges for most potting substrates: total porosity 50 to 85%, air space 10 to 30%, container capacity 45 to 65%, available water 25 to 35% and unavailable water, held at 1500 kPa, 25 to 35% (their Table 1 prints 23 to 35% for both). So a mix reading 30% can be close to its wilting point, while 30% in a loam is wetter than field capacity. Bilderback’s team measured their own substrates in standard 3-inch-tall sampling cylinders, and they note that container height changes air space and container capacity.

That height effect is the perched water table. After watering, a layer at the bottom of every container stays saturated, and it is a bigger share of a short container (Fonteno, Bailey and Nelson, NC State). Their 1:1 peat and vermiculite mix had 0.5% air space in a 648-cell plug tray, 2.8% in a 288-cell tray, 13% in a 4-inch pot and 20% in a 6-inch pot. One sponge shows it too: 4.2% air space standing 2 inches tall, 14.8% at 4.25 inches and 46.5% at 8.5 inches. Bilderback’s team warns that too little air space risks waterlogging and root anoxia.

So the bottom of a pot is its wettest zone after drainage, and probe depth changes the reading. A mix that drains well in a tall pot can stay too wet in a shallow one.

How to read the number on your sensor

  1. Check what the number is. A dial scale, a raw count or a “%” with no stated calibration is not VWC. E-618 says all soil water sensing methods must be calibrated, “despite the efforts of manufacturers to provide calibration curves,” and exempts only the tensiometer. METER rates its own sensors’ generic calibration at about ±3 to 4% VWC in most mineral soils and ±5% in soilless substrates, and ±1 to 2% after soil-specific calibration. See capacitive vs. resistive sensors for why cheap probes drift and how to calibrate a soil moisture sensor to fit your own curve.
  2. Watch the shape after watering. The reading jumps, then falls. In METER’s field data water content “decrease[s] quickly and then finally flatten[s] out,” in most soils within about three days. Outdoors that plateau is field capacity at that depth. In a pot it is the drained water content at the probe’s depth, which depends on the mix, the pot height and where the probe sits. The slower decline after it is mostly the plant and evaporation from the surface drawing water down, plus some slow drainage.
  3. Read it as a share of your own range. Note the plateau and the reading when the plant needs water by your usual check. Example: a pot settles at 40% and is due at 22%. A reading of 31% means half the range is used: (40 − 31) / (40 − 22) = 0.5.
  4. Keep the probe put. Those endpoints belong to that pot, mix and probe depth, and METER names air gaps from poor installation as the largest threat to accuracy. After repotting or moving the probe, set both again.

Sources

  1. The researcher's complete guide to soil moistureMETER Group
  2. Plant available water: How do I determine field capacity and permanent wilting point?METER Group
  3. Irrigation Monitoring with Soil Water SensorsTexas A&M University System, Extension publication E-618 (Enciso, Porter, Evett, Périès and Peters)
  4. Soil and Water RelationshipsSoils Laboratory Manual: K-State Edition, Moorberg and Crouse (Kansas State University / New Prairie Press)
  5. Properties of Greenhouse SubstratesNC State University, Fonteno, Bailey and Nelson (N.C. Flower Growers' Bulletin, 1995)
  6. Healthy Substrates Need Physicals Too!HortTechnology, Bilderback, Warren, Owen and Albano, 2005 (hosted by USDA ARS)

General information, not professional advice for a specific plant or crop. Spot something wrong? Email info@terrathink.io.

Keep reading

All field notes

Join the waitlist

New field notes by email, and first word when the hardware goes live.

By joining, you agree to get email updates from Terrathink. Unsubscribe anytime. Privacy policy