Field NotesPlant scienceNo. 20
How to measure plant growth: height, leaf area, biomass and growth rate
Height is the easiest growth number to take and the easiest to misread. Leaf area, dry mass and relative growth rate show how much plant you grew, and how fast for its size.

The short answer Track more than height. Measure height to a fixed point, leaf count, stem diameter and leaf area on the same plants over time, then harvest some and dry them until the weight stops dropping (research protocols use about 70°C for 48 hours). Compare growth with relative growth rate: the change in the average natural log of dry mass divided by the days between harvests.
A plant that gained 3 cm might have added a stack of new leaves, or it might have stretched toward a dim window. The plant records its growth in leaves, stem and roots; height is only the easiest part to read. To build a fair experiment around these measures, see plant science fair project ideas.
Why height alone misleads
Writing about forest seedlings, Diane Haase (Oregon State University) notes that height and stem diameter are “easy and quick to measure,” then adds: “These two shoot measures alone, however, are inadequate to assess the seedling condition fully.”
Height ignores leaves, branches, stem thickness and roots, and it responds to light quality. Poorter and colleagues explain that plants sense neighbors through the ratio of red to far-red light, which is 1.2 in sunlight but as low as 0.2 in light passing through or reflected off leaves, and that a high ratio “results in reduced extension growth.” That suggests a crowded plant’s height can partly reflect its neighbors, not just how much it grew. How much light houseplants need covers the light side.
Haase also describes a sturdiness ratio for seedlings: height divided by stem diameter, in the same units. A high value indicates a relatively spindly seedling.
Non-destructive measures: height, leaves and stem
You can repeat these on the same plants.
- Height to a fixed point. The plant trait handbook by Pérez-Harguindeguy and colleagues measures from ground level to the top of the main photosynthetic tissue, not counting flowers. Potting soil settles, so fix the reference: Haase measures forest seedlings from the cotyledon scar (where the seed leaves were attached) to the top bud. For older plants, measure from the pot rim and note that you did.
- Leaf count. Decide what counts (an unfolding tip, say) and apply it to every plant.
- Stem diameter. Use calipers at a marked spot, held perpendicular to the stem. For forest seedlings, Haase notes that diameter “has been considered the best predictor of field survival and growth.”
How to measure leaf area
Grid paper. Trace the leaf onto 1 cm graph paper and count squares (each is 1 cm²), with a rule set in advance for squares the outline cuts. UF/IFAS lists grid counts among traditional methods now rarely used in horticultural research because they are slow.
Length × width. The trait handbook uses a separate sample of about 20 leaves to find the regression slope of leaf length × width against leaf area. Measure those leaves by grid or photo. Example (made-up slope): at 0.65, a leaf 8 cm by 5 cm is about 0.65 × 8 × 5 = 26 cm². Leaf shape sets the slope, so fit one per species.
Photo with a scale. UF/IFAS publication HS1395 describes a non-destructive method using a phone and ImageJ, a free, public-domain image program:
- Flatten the leaf under a clear sheet beside a reference of known size (they used a 3-inch sticky note on a red clipboard). Hold the camera square to the board so reference and leaf sit the same distance from the lens, and avoid deep shadows.
- In ImageJ, draw a straight line across the reference and enter its real length under Analyze > Set Scale.
- Crop to the leaf, separate it from the background with Image > Adjust > Color Threshold, then run Process > Binary > Make Binary.
- Tick Area and Limit to threshold under Analyze > Set Measurements, then run Analyze > Measure.
Area then comes out in calibrated units such as square millimeters, and Analyze Particles measures several separate leaves in one image (ImageJ documentation). Against a laboratory leaf area meter on 100 hop and 100 pepper leaves, the UF method agreed nearly 1:1, at 1.5 to 2 minutes of processing per image.
Destructive measures: fresh mass, dry mass and root:shoot ratio
Harvesting shows how much plant you grew, roots included, but each plant can be weighed only once.
- Fresh mass includes whatever water the plant holds at that moment, so it shifts with watering and wilting. The handbook says RGR is ideally measured “on a dry-mass basis for the whole plant, including roots.”
- Dry mass. Wash soil gently off the roots (the handbook warns fine roots are especially hard to separate from soil) and dry the parts in labeled paper envelopes. Research protocols dry at about 70°C: at least 48 hours at 70°C (158°F) in the handbook’s growth-rate protocol, 48 hours at 68°C (about 154°F) in Haase’s forest-seedling work. Whatever temperature you use (the science fair note uses 100°F overnight), reweigh after a few more hours: a sample still losing mass isn’t dry. Dry every sample the same way, and have an adult run the oven.
- Root:shoot ratio is root dry mass ÷ shoot dry mass. The handbook prefers root mass fraction (root dry mass ÷ total dry mass) because it stays between 0 and 1, while root:shoot “can vary from a tiny to a very large number.” Example: 0.3 g of roots and 0.9 g of shoot give root:shoot 0.33 and root mass fraction 0.3 ÷ 1.2 = 0.25. Compare plants of similar mass.
| Measure | Tools | Destructive? | Best for |
|---|---|---|---|
| Height | Ruler | No | Frequent tracking |
| Leaf count | Tally sheet | No | Young plants |
| Stem diameter | Calipers | No | Sturdiness |
| Length × width | Ruler, calibration leaves | No | Leaf area over time |
| Grid paper | Graph paper | Usually | A few leaves |
| Photo + ImageJ | Camera, scale, software | No | Many leaves |
| Dry mass | Oven, scale | Yes | Final comparisons, RGR |
| Root mass fraction | Oven, scale | Yes | Growth below ground |
Growth rate: absolute and relative
Absolute growth rate is the gain per day:
AGR = (W₂ − W₁) ÷ (t₂ − t₁)
W₁ and W₂ are the measurements (dry mass, leaf area or height) at times t₁ and t₂, in days; units are grams (or cm², or cm) per day.
Big plants add more per day simply because they’re big. Relative growth rate measures gain against the size already there, so, in the handbook’s words, “growth rates can be compared among species and individuals that differ widely in size.” Hoffmann and Poorter (2002) write it as:
RGR = (ln W₂ − ln W₁) ÷ (t₂ − t₁)
ln is the natural logarithm (=LN() in a spreadsheet), W₁ and W₂ are plant dry weights at times t₁ and t₂, and units are g g⁻¹ d⁻¹: grams of new growth per gram of plant per day.
Their main point: take the ln of each plant’s weight, then average. Averaging weights first biases RGR whenever the spread of ln weights changes between harvests, so they recommend the mean of the logs “exclusively.”
Worked example (made-up numbers). Four plants harvested on day 14 weigh 0.40, 0.50, 0.60 and 0.70 g dry; four harvested on day 21 weigh 0.70, 0.90, 1.10 and 1.30 g.
- ln, day 14: −0.916, −0.693, −0.511, −0.357; mean −0.619
- ln, day 21: −0.357, −0.105, 0.095, 0.262; mean −0.026
- RGR = (−0.026 − (−0.619)) ÷ (21 − 14) = 0.593 ÷ 7 = 0.0847 g g⁻¹ d⁻¹
- AGR from mean weights (0.55 and 1.00 g) = 0.45 ÷ 7 = 0.064 g per day
The ln of the mean weights gives 0.598 ÷ 7 = 0.0854, close here because the spread of ln weights barely changed, but not the method to rely on.
Why it matters, in another made-up case: a 1.0 g plant reaching 1.5 g in a week beats a 0.10 g seedling reaching 0.18 g on AGR (0.071 vs. 0.011 g per day) but loses on RGR (0.058 vs. 0.084). The handbook notes RGR “generally decreases over time, the more so in fast-growing species,” so compare plants of the same age and similar starting size. On a plot of mean ln mass against time, RGR is the slope. For graphing the raw measurements with averages and error bars, see how to graph plant growth data.
How many plants to measure, and how often
- Start even. Grow extra plants and choose similar-sized ones (the handbook), or remove the smallest and largest just before treatment starts (Poorter and colleagues).
- Replicates depend on spread. Poorter’s group measures variability as the standard deviation of ln-transformed dry mass or leaf area: below 0.2 is low, above 0.6 high. In their examples, at 0.15 a difference above 50% was easily detected with 4 or 5 plants; at 0.6, even 15 plants couldn’t reliably detect a 100% difference.
- Harvests. At least one initial and one final, spaced so plants less than double in mass between them (the handbook’s rule of thumb). The example above, 1.8-fold in 7 days, fits.
- Non-destructive tracking. The handbook suggests about 10 to 15 plants per treatment, cautioning that “repeated handling may cause growth retardation.” For timing, the science fair note measures every 2 to 3 days.
Sources of error
- Pot size. Poorter and colleagues found “almost invariably a strong positive correlation between plant growth and pot volume,” and say a pot is “certainly small” once total plant dry mass exceeds 2 g per liter of rooting volume. Use the same pots throughout.
- Position. Light can drop 20 to 50% near the walls of a growth room, and edge plants grow in different conditions. Rearrange plants during the experiment, or leave edge plants out of the data.
- Hidden leaves. In some rosette species, overlap can hide more than half the leaf area, which limits photos of whole plants.
- Photo setup. Check that the threshold outline matches the leaf, and decide once whether leaf stalks count.
Sources
- Avoiding Bias in Calculations of Relative Growth RateAnnals of Botany 90(1):37-42, Hoffmann and Poorter, 2002 (via PubMed Central)
- New handbook for standardised measurement of plant functional traits worldwideAustralian Journal of Botany 61(3):167-234, Pérez-Harguindeguy et al., 2013 (CSIRO Publishing)
- The art of growing plants for experimental purposes: a practical guide for the plant biologistFunctional Plant Biology 39(11):821-838, Poorter et al., 2012 (CSIRO Publishing)
- Understanding Forest Seedling Quality: Measurements and InterpretationTree Planters' Notes 52(2):24-30, Haase (Oregon State University Nursery Technology Cooperative), 2008 (hosted by RNGR)
- A Simple, Inexpensive, and Portable Image-Based Technique for Nondestructive Leaf Area MeasurementsUF/IFAS Extension, publication HS1395 (Agehara, Pride, Gallardo and Hernandez-Monterroza, 2020)
- Analyze MenuImageJ documentation (imagej.net)
General information, not professional advice for a specific plant or crop. Spot something wrong? Email info@terrathink.io.


