Field NotesPlant scienceNo. 02

How much light does a houseplant need? Lux, PPFD and DLI, explained

Your eyes are a poor light meter, and a few feet from a window can mean several times less light. Here is what the numbers mean and how to get them.

A monstera on a white stand, with window-blind light and leaf shadows across a cream wall

The short answer By University of Missouri Extension’s ranges, low-light houseplants want 50 to 250 foot-candles (roughly 540 to 2,700 lux) at the leaves, medium-light plants 250 to 1,000, and high-light plants more than 1,000. As a daily total, Iowa State puts foliage houseplants at about 3 to 10 mol/m²/day of light (DLI). Even low-light plants usually don’t get enough more than 10 feet from an average window.

Light is the one need you can’t judge by eye. University of Florida Extension points out that a desk by a window may be ten times brighter than a workspace across the hall that looks only slightly darker. Your eyes adjust so well that they hide the difference, which is why it pays to put numbers on it.

Lux, PPFD and DLI: three different questions

Foot-candles and lux: how bright does it look to you? These are units built around human vision. Lux is one lumen per square meter, and 1 foot-candle equals 10.76 lux (Iowa State). The lumen is defined at about 555 nm, near the peak of the eye’s sensitivity curve (Apogee Instruments), so lux counts yellow-green light heavily and red and blue light less.

PAR and PPFD: how many usable photons are arriving right now? Plants photosynthesize with light between 400 and 700 nm, called photosynthetically active radiation (PAR). PPFD (photosynthetic photon flux density) is how many PAR photons land on a square meter each second, in micromoles: µmol/m²/s. This is what a quantum sensor reads (Virginia Tech).

DLI: how much did the plant get today? Daily light integral is the total photosynthetic light a plant receives over one day, in moles per square meter per day (mol/m²/day). Think of PPFD as a speedometer and DLI as the trip odometer. For a light with steady output, Iowa State gives the math:

DLI = PPFD × hours × 0.0036

A grow light delivering 200 µmol/m²/s for 16 hours works out to about 11.5 mol/m²/day (Virginia Tech’s example).

Why window distance and direction matter so much

Indoor light falls off fast. UF Extension notes that outdoor light at noon can top 4,000 foot-candles even in winter, while a north-facing window may never reach 400, and an office lit only by fluorescent fixtures often sits at 40 foot-candles or less.

Direction sets the ceiling. Missouri Extension says south windows give the brightest light for the longest part of the day, east and west windows suit many medium-light plants, and north windows are satisfactory only for low-light plants. Distance does the rest: Missouri notes that even low-light plants usually don’t get enough light more than 10 feet from an average window.

For scale, Virginia Tech’s guide gives average outdoor DLI in Virginia of about 40 to 45 mol/m²/day in July and 15 to 20 in December, measured in open ground away from trees and buildings. A houseplant across the room gets a small slice of that.

Typical ranges for houseplants

The sources don’t agree exactly, so here they are side by side.

Light level Foot-candles (Missouri) Foot-candles at mid-day (UF/IFAS) DLI, mol/m²/day (Iowa State) Where UF/IFAS finds it
Low 50 to 250 25 to 100 3 to 6 Far from windows or in heavy shade
Medium 250 to 1,000 100 to 500 6 to 10 Unshaded north window, shaded east or west window
High 1,000 or more 500 to 1,000 12 to 16 Unshaded east or west window, shaded south window
Direct sun Not separated Over 1,000 Not separated Right at an unshaded south or southwest window

Iowa State puts foliage houseplants in the low and medium DLI groups, flowering houseplants in medium and high, and succulents in high.

The foot-candle and DLI figures describe different goals. Convert UF’s low-light ceiling of 100 foot-candles and you get about 20 µmol/m²/s; even if that noon level held for 12 straight hours, it would add up to under 1 mol/m²/day, well below Iowa State’s low-light range. Missouri draws the same line: it says a few low-light plants can be maintained at as little as 10 foot-candles under artificial light, while medium-light plants grow best above 750. Treat the lower numbers as what a plant will tolerate and the higher ones as what it takes to keep it growing.

Converting lux to PPFD, and why the factor changes

To turn a lux reading taken in sunlight into an approximate PPFD, multiply by 0.0185 (the same as dividing by 54), the factor published by sensor maker Apogee Instruments. So 5,000 lux of daylight is about 93 µmol/m²/s. In foot-candles, Virginia Tech’s factor for sunlight is 5.01 foot-candles per µmol/m²/s, which gives about 200 µmol/m²/s for 1,000 foot-candles.

The factor is different for every light source, because lux weights light by how the eye sees it while PPFD counts all PAR photons alike. Apogee’s factors to get PPFD from lux:

  • Sunlight: 0.0185
  • Cool white fluorescent: 0.0135
  • Metal halide: 0.0141
  • High pressure sodium (mogul base): 0.0122

That 5,000 lux under cool white fluorescent tubes is only about 68 µmol/m²/s. LED grow lights aren’t on these lists, and their spectra vary, so Iowa State’s advice applies: set the meter or app for the light source you’re actually measuring. The PPFD, lux and DLI calculator applies these factors for you and adds up the DLI.

How to measure the light your plant gets

Where to hold it. Iowa State says to always measure at foliage level. Put the sensor where the leaves are, facing the way they face, not on the windowsill in front of them. UF’s table uses mid-day readings, so measure around midday, on a sunny day and again on an overcast one.

A light meter. UF Extension says a handheld digital meter reading foot-candles or lux, accurate to one foot-candle, is often the best tool for the job. A quantum (PAR) sensor reads PPFD directly; Virginia Tech puts standalone units anywhere from under $100 to over $1,000. Plant sensors compared covers how accurate each kind is, including under LED grow lights.

A phone app. Apps estimate light from the phone’s built-in light sensor. Virginia Tech says a $20 app could give homeowners useful information, and Iowa State calls their accuracy adequate for the typical home gardener. UF is more cautious: accuracy varies with the device and the calculation method, so use apps to spot changes in light and treat the numbers as approximations.

There’s data behind that caution. In a 2017 study in Applied Sciences, one uncalibrated phone sensor was off by about 39% on average against a reference lux meter, and by about 62% below 100 lux. Above 500 lux its error was under 5%. The study tested only three phones under one incandescent bulb, but the pattern is useful: phone readings are least reliable in dim light, exactly where low-light decisions get made. Use the same phone, held the same way, to compare spots against each other.

Using grow lights

Grow lights make DLI easy to plan because their output is steady. Work backward from the target: to hit 6 mol/m²/day over 12 hours, you need about 140 µmol/m²/s at the leaves (6 ÷ 12 ÷ 0.0036).

  • Hours. Iowa State recommends 12 to 14 hours a day for most indoor growing, with a range of 10 to no more than 16 hours for home gardeners. Missouri suggests 16 to 18 hours for plants that get no outdoor light at all. Use a timer; Missouri recommends a grounded plug since there’s water nearby.
  • Distance. Missouri puts plant tips 6 to 12 inches from the source, and its measurements show how quickly light drops: under two 40-watt fluorescent tubes, about 260 foot-candles at 1 foot, 110 at 2 feet and 40 at 4 feet. Iowa State notes that moving a fixture closer raises intensity over a smaller area, and high-output fixtures can damage leaves with heat.
  • Spectrum. Iowa State considers a “full spectrum” or “daylight” fixture with a mid-range Kelvin rating ideal; mixing warm white and cool white bulbs also broadens the spectrum. UF says cool white works well.
  • Ignore watts. Iowa State says wattage is not a reliable indication of light intensity. Measure at the leaves instead.

Too little or too much light is also one of the causes to rule out when leaves turn yellow.

Sources

  1. Calculating and Using Daily Light Integral (DLI): An Introductory GuideVirginia Cooperative Extension (Virginia Tech)
  2. Important Considerations for Providing Supplemental Light to Indoor PlantsIowa State University Extension and Outreach
  3. Light for HouseplantsUniversity of Florida IFAS Extension, Gardening Solutions
  4. Lighting Indoor Houseplants (G6515)University of Missouri Extension
  5. PPFD to Lux ConversionApogee Instruments
  6. Smartphones as a Light Measurement Tool: Case of StudyApplied Sciences 7(6):616 (2017), MDPI

General information, not professional advice for a specific plant or crop. Spot something wrong? Email info@terrathink.io.

Keep reading

All field notes

Join the waitlist

New field notes by email, and first word when the hardware goes live.

By joining, you agree to get email updates from Terrathink. Unsubscribe anytime. Privacy policy