Field NotesPlant techNo. 10
EC and pH for plants: what the numbers mean and how to measure them
EC tells you how much dissolved salt, mostly fertilizer, is around the roots. pH affects how much of it the roots can use. Both depend on how you sample, so here is how to get a reading you can trust.

The short answer EC (electrical conductivity) measures the total dissolved salts, mostly fertilizer, in water or in the solution around the roots, usually in mS/cm (the same as dS/m and mmho/cm). pH measures acidity and affects how available those nutrients are to roots. Extension guides put soilless potting mix at about pH 5.4 to 6.2 and hydroponic solutions at 5 to 6; the right EC depends on how you sampled, so compare each reading with the range for that method.
An EC pen and a pH pen give you two numbers in seconds. Making them mean something takes three habits: know the unit, sample the same way every time, and keep the meter calibrated.
What EC measures
Fertilizer goes into water as salts. Dissolved, they break into ions that carry electric current, so conductivity rises as you add them (Oklahoma State University Extension). Purdue Extension calls EC a measure of the dissolved salt concentration in a growing substrate and of the fertilizer available for growth.
EC counts ions, not specific nutrients, so it can’t tell nitrate from sodium. Oklahoma State advises replacing a hydroponic solution completely every two weeks, because nutrient ratios drift as you top it up with water and nutrients; sodium chloride, for example, can build up to toxic levels.
The units you’ll see:
- mS/cm (millisiemens per centimeter) is the usual horticulture unit. UMass Extension notes that 1.0 mmho/cm = 1.0 dS/m = 1.0 mS/cm.
- µS/cm (microsiemens per centimeter) is a thousandth of that, so the number is 1,000 times larger: 1.41 mS/cm is about 1413 µS/cm (Michigan State University Extension).
Temperature shifts the reading too. A cooled solution conducts less because its ions have less energy, and for neutral salts the change (the temperature coefficient, β) is typically 1.5 to 2.2% per °C, according to Hanna Instruments. Meters with automatic temperature compensation correct the reading to a reference temperature, typically 25 °C or 20 °C (Hanna Instruments); check which yours uses. Example: at 2% per °C, a solution 10 °C below the reference reads about 20% low uncompensated. Purdue recommends meters with automatic temperature compensation.
EC, TDS and the ppm problem
Many pens also show ppm (often labeled TDS, total dissolved solids). That isn’t measured; the meter multiplies EC by a factor:
ppm = EC × k
where EC is the reading in mS/cm and k is the meter’s ppm scale.
Meter maker Bluelab names three scales in wide hydroponic use: 500, 650 and 700. The 500 scale, also called TDS, is based on sodium chloride; the 700 scale is based on potassium chloride. Bluelab says a US feeding chart could use the 650 or 500 scale, a UK one the 700.
Example, one solution on each scale:
| EC (mS/cm) | EC (µS/cm) | 500 scale (ppm) | 650 scale (ppm) | 700 scale (ppm) |
|---|---|---|---|---|
| 1.0 | 1,000 | 500 | 650 | 700 |
| 1.5 | 1,500 | 750 | 975 | 1,050 |
| 2.4 | 2,400 | 1,200 | 1,560 | 1,680 |
The 500 and 700 values in the 2.4 row match Bluelab’s worked example. At 1.5 mS/cm, two pens can disagree by 300 ppm on the same water. Bluelab notes that true ppm takes a chemical analysis and recommends working in EC. If a chart gives ppm, find its scale before you mix. The EC to ppm converter switches between EC and all three scales.
pH: what it affects and where to aim
pH measures how acidic or basic a solution is, from 0 to 14 with 7 as neutral (Oklahoma State). It affects how much of the fertilizer that EC detects the roots can use. Purdue notes that pH affects nutrient availability, especially of micronutrients, and that all nutrients are readily available from pH 5.4 to 6.2, though each species has its own optimum.
Targets depend on what the roots grow in:
- Soilless potting mix: 5.4 to 6.2 (Purdue). UMass Extension’s target is narrower, 5.5 to 6.0.
- Mix with 20% or more field (mineral) soil: 6.2 to 6.5 (UMass).
- Hydroponic nutrient solution: 5 to 6, usually 5.5, which Oklahoma State says keeps the root environment at 6 to 6.5.
Oklahoma State’s crop table gives optimum hydroponic EC ranges: 1.0 to 1.6 mS/cm for basil, 1.2 to 1.8 for lettuce, 2.0 to 4.0 for tomato. Its crop pH ranges sometimes run higher (lettuce: 6.0 to 7.0) and don’t say whether they mean the solution or the root zone.
Water with alkalinity above 75 ppm raises solution pH, so check pH more often if yours tests high (Oklahoma State).
How to test a potted plant’s root zone
The PourThru method tests the solution the roots are sitting in, without disturbing the mix. Purdue Extension’s steps:
- Water or feed as usual. If you feed weekly, test on the same day of the cycle each time.
- Let the pot drain for 30 to 60 minutes, then set it in a saucer.
- Pour distilled water onto the mix: about 75 mL (2.5 oz) for a 4- to 6-inch pot, 100 mL (3.4 oz) for 6.5-inch, 150 mL (5 oz) for 1 gallon, 350 mL (12 oz) for 3 gallons.
- Collect about 50 mL of the liquid that drains out (the leachate). More than 70 mL can dilute the salts; less than 50 mL may not cover the probe.
- Measure its EC and pH.
Purdue suggests averaging five to ten pots per crop and container size; with a few houseplants, test the same pots each time.
The other two methods test a scoop of mix (Purdue). For a saturated media extract (SME), take 200 to 300 mL from the root zone, skipping the top and bottom inch, which can hold more salt; add distilled water just to saturation with none pooling on top, wait 30 minutes, filter and measure. For a 1:2 dilution, stir one part mix into two parts distilled water by volume, then wait, filter and measure the same way.
Each method has its own scale. Purdue’s interpretation, in mS/cm:
| Level | PourThru | SME | 1:2 | What it means (Purdue) |
|---|---|---|---|---|
| Very low | 0 to 0.9 | 0 to 0.75 | 0 to 0.25 | May be too little for rapid growth |
| Low | 1.0 to 2.6 | 0.76 to 2.0 | 0.26 to 0.75 | Suits seedlings, bedding plants, salt-sensitive plants |
| Normal | 2.7 to 4.6 | 2.1 to 3.5 | 0.76 to 1.25 | Most established plants; upper limit for salt-sensitive ones |
| High | 4.7 to 6.5 | 3.6 to 5.0 | 1.26 to 1.75 | Reduced vigor and growth, especially in hot weather |
| Very high | 6.6 to 7.8 | 5.1 to 6.0 | 1.76 to 2.25 | May cause salt injury from reduced water uptake; leaf edge burn, wilting |
| Extreme | Above 7.8 | Above 6.0 | Above 2.25 | Most crops injured; leach immediately |
Sources differ. UMass Extension’s lab uses a saturated paste extraction and calls 1.5 to 3.0 mS/cm normal for established plants in soilless mix; Purdue’s SME band is 2.1 to 3.5. For houseplants, Purdue lists African violets, begonias and orchids as light feeders (PourThru 1.0 to 2.6 mS/cm) and kalanchoe and hibiscus as medium feeders (2.0 to 3.5). UMass’s 0.5 to 0.8 for interior plantings is by saturated paste, and UMass says light level and growth rate matter most indoors.
What off-target numbers look like on the plant
High EC. UMass says salts above the normal range for long periods may cause root injury, leaf yellowing, burned margins and sometimes wilting; seedlings, young transplants and plants in mixes with 20% or more field soil are less tolerant. Usually the cause is more fertilizer than the plant needs; too little watering and leaching, poor drainage, or damaged roots can also do it (UMass). Because salt cuts water uptake (Purdue), a plant can wilt in wet mix. At extreme readings, Purdue says to leach immediately: run plenty of clear water through the pot.
Low EC. Below the normal range, the plant may need more fertilizer (UMass). In hydroponics, very low EC usually comes with nutrient deficiencies and slower growth (Oklahoma State).
Low pH. UMass calls this the most common pH problem in Massachusetts greenhouse mixes. Calcium and magnesium may run short, and below pH 5.8, iron and manganese can reach toxic levels for geraniums, New Guinea impatiens and many bedding plants.
High pH. Availability falls on this side too, especially of micronutrients (Purdue), and Purdue cites high-pH chlorosis (yellowing) in calibrachoa and maple. Leaf patterns that point to pH or nutrient trouble are in why are my plant’s leaves turning yellow. If you also use a soil moisture probe, our capacitive vs. resistive comparison explains how fertilizer salts affect each type.
Calibrating and caring for your meters
- pH: calibrate at two points. Buffers usually come in pH 4, 7 and 10 (Oklahoma State); Michigan State uses 4.01 and 7.01. Purdue says to calibrate for the range you’re testing, which for peat or bark may mean calibrating at 4.0.
- EC: use a standard solution, usually 1.41 mS/cm (Oklahoma State), which may be labeled 1413 µS/cm (Michigan State). With the probe in the standard, set the meter to that value.
- Standards: pour some into a clean, dry cup; dipping the probe in the bottle throws the standard off over time. Check expiration dates, rinse the electrode with distilled water before and between buffers, and note the buffer’s temperature, since pH changes with it (Michigan State).
- Storage: keep meters and solutions in a low-humidity room at room temperature, never in a greenhouse or outdoors (Purdue). Store the pH electrode as its manual directs so the tip stays wet. One left unused for long has likely dried out: follow the manufacturer’s instructions to re-wet it (the Michigan State author’s probe needed at least an hour in storage solution), then recalibrate.
- Schedule: in hydroponics, check pH and EC daily at the same time of day, adjusting pH after EC is in range (Oklahoma State). Recalibrate after any long break, and as your meter’s manual directs.
Keep your readings comparable
Write the method, unit and ppm scale beside every number. A PourThru reading of 3.0 mS/cm is normal for most established plants; by SME it’s in the upper half of normal, and by 1:2 it’s extreme. Test at the same point in the cycle with the same meter, so readings from week to week are comparable.
Sources
- HO-237: pH and Electrical Conductivity Measurements in Soilless SubstratesPurdue University Extension, Horticulture and Landscape Architecture (Camberato, Lopez and Mickelbart)
- Soil Test Report - Commercial FloricultureUMass Extension
- Electrical Conductivity and pH Guide for HydroponicsOklahoma State University Extension (Singh and Dunn)
- Calibrate your pH and EC meter in your greenhouseMichigan State University Extension (Wollaeger, 2016)
- Why do I need temperature compensation for measuring EC?Hanna Instruments Knowledge Base
- What are the different conductivity scales? What do they mean?Bluelab Support
General information, not professional advice for a specific plant or crop. Spot something wrong? Email info@terrathink.io.


