Field NotesClassroomNo. 21
How to set up a classroom grow light for seedlings: height, hours and DLI
Seedlings on a windowsill tend to grow tall and thin. Here is how high to hang a grow light, how long to run it, how to check it and how to keep cords and water apart.

The short answer Hang fluorescent shop lights 2 to 4 inches above the seedlings, on chains so you can raise them, and run them 12 to 16 hours a day on a timer (University of Minnesota Extension); start an LED at its maker’s recommended height. Iowa State and Purdue figures point to roughly 10 to 12 mol/m²/day of light at the leaves. Plug into a GFCI-protected outlet.
Set up well, a light cart gives students stocky seedlings and data worth graphing. Set up badly, it makes light a variable nobody meant to test.
Why a windowsill usually isn’t enough
University of Minnesota Extension (UMN) is blunt: “A windowsill is not a good location for starting seeds.” Spring sunlight in Minnesota is “relatively weak compared to artificial light sources kept close to the plants,” cloudy days bring very low light, and a sill can be the coldest spot in a house at night and the hottest by day. Windowsill seedlings tend to be too tall, with thin, bent stems, and UMN calls lack of light “the major cause of elongated, skinny stems.”
A roomy south-facing sill may do for a few plants, UMN allows, but light drops fast with distance from the glass (how much light does a houseplant need has the numbers).
How much light and how many hours seedlings need
The target is a daily light integral (DLI), the day’s total photosynthetic light in mol/m²/day.
- DLI. Iowa State University Extension lists “starting seedlings” at the high side of its medium range (6 to 10 mol/m²/day) and the low side of its high range (12 to 16). Purdue Extension reports that seedlings of five bedding plants, including marigold and impatiens, improved in quality at transplant as DLI rose up to 12. Together they point to roughly 10 to 12, a synthesis rather than a seedling range either source states. Purdue’s data come from greenhouse bedding plants, so treat it as a starting target.
- Hours. UMN says seedlings need 12 to 16 hours a day. Iowa State calls 12 to 14 generally best indoors, with no more than 16 for home gardeners. University of Missouri Extension’s houseplant guide suggests 16 to 18 for plants with no outdoor light. In a dim room, 16 hours is the figure all three allow. Never run lights around the clock: UMN notes many plants need a dark period each night.
Use a timer: Missouri says lights should go on and off “regularly and consistently.” Give every tray the same hours unless day length is your variable; Iowa State warns that changing the hours can change a photoperiodic plant’s flowering response. UMN adds: don’t plug a heat mat into the light timer.
Choosing a fixture: tubes or LEDs, white or red and blue
You don’t need a fixture labeled “grow light.” UMN says standard fixtures with two cool white fluorescent tubes “give plants adequate light and are inexpensive.” Missouri is less sure: it finds cool white usually short on red and suggests one plant-growth tube per one or two cool white.
- LEDs. Missouri calls LEDs “extremely energy-efficient and very long-lived,” with very little heat. Skip incandescent bulbs, which run too hot to place close.
- White or red and blue. Plants primarily use red and blue light (Iowa State), and a 2020 Horticulture Research paper reports that the first commercial blue and red LED fixtures produced more light per watt than white ones. But it notes that high color fidelity helps people spot “tiny insects, nutritional disorders, and diseases.” For students judging leaf color, white is the practical choice.
- Watts are not light. Iowa State says watts “are not a reliable indication of light intensity because they measure the amount of energy the fixture uses,” and names photosynthetic photon flux (PPF, in µmol/s) as a more useful measure for plants. The Horticulture Research paper put typical horticultural LED fixtures at 2 to 3 µmol of photons per joule in 2020. A watt is a joule per second, so a 40-watt horticultural fixture would emit roughly 80 to 120 µmol/s, an estimate (the paper doesn’t cover ordinary shop lights). Compare PPF if the spec sheet lists it.
How far above seedlings to hang the light
UMN: keep lights “no more than 4 inches above the tops of your seedlings: as close as 2 inches is ideal.” Missouri says to place seedlings “within a few inches of the tubes as soon as germination begins,” and puts most other plants with their tips 6 to 12 inches from the light.
- Keep it adjustable. Hang the fixture from chains (UMN) or adjustable hangers so you can hold the distance, as Missouri advises. Have students record bulb-to-leaf distance with a ruler. Remove clear domes once seedlings touch them (UMN).
- LEDs. Those inch figures come from guides written mainly around fluorescent tubes, and neither gives a distance for LEDs. Moving a fixture closer raises intensity over a smaller area (Iowa State), so start an LED at the maker’s recommended height and adjust by meter.
The seedlings report on this daily: Missouri’s signs of too little light include long internodes (stretched stem between leaves) and pale green stems and foliage.
Heat. Tubes and LEDs produce relatively little heat (Missouri), but a fixture that runs hot warms plants more as it moves closer (Iowa State), and excess heat can dry out the mix (UMN). If a thermometer at leaf height reads well above room temperature, raise the light.
Checking the light: meter, phone app and calculator
Iowa State says to “always measure light intensity at the foliage level,” with the meter or app set for your light source. PAR meter vs. lux meter covers meters and phone apps. The PPFD, lux and DLI calculator converts lux to PPFD for fluorescent and other listed sources; for LEDs, use the maker’s factor or a PAR meter.
For a light on a timer, Iowa State’s formula turns a reading into the day’s total:
DLI = PPFD × hours × 0.0036
DLI is in mol/m²/day. PPFD is the reading at the leaves, in µmol/m²/s. Hours is how long the light runs each day. 0.0036 converts units (3,600 seconds per hour divided by 1,000,000 µmol per mol).
Check the edges. Fluorescent tubes give less light at their ends than at the center (Missouri), so use a fixture at least as long as the trays. A Missouri table lists 260 foot-candles 1 foot below two standard 40-watt tubes, but 200 a foot to either side; with a reflector, 400 below. Read the center, ends and corners of each shelf.
Worked example (made-up numbers). A shelf runs 16 hours a day. The meter reads 180 µmol/m²/s at the center and 110 at a corner.
- Center: 180 × 16 = 2,880; 2,880 × 0.0036 = 10.4 mol/m²/day.
- Corner: 110 × 16 = 1,760; 1,760 × 0.0036 = 6.3 mol/m²/day.
The center meets the 10 to 12 target; the corner falls short. Reaching 11 in 16 hours takes about 190 µmol/m²/s: 11 ÷ (16 × 0.0036) = 11 ÷ 0.0576 ≈ 191. Sixteen hours is already the most UMN and Iowa State allow, so fix the corners with height and reflection, not more hours.
Even it out. Missouri says white paint or aluminum foil “beneath or around the growing area helps reflect light”; white poster board on the back and sides works the same way. Keep foil clear of plugs. Center the trays and swap them every few days so no treatment always sits in the dim corner. Classroom plant experiments with sensors builds a light investigation on this setup.
Water, electricity and the school’s rules
- Water from below. UMN suggests adding water to the tray so it moves up into the mix, then draining what’s left “to keep the roots healthy.”
- Ground it. Missouri says the timer’s cord should be the three-prong type, because “the use of water around plants makes grounding electrical fixtures important.”
- Use a GFCI. A ground-fault circuit interrupter cuts power when current going out and coming back differs by as little as 0.006 amperes, and is designed to act before the electricity can affect your heartbeat, says the U.S. Consumer Product Safety Commission (CPSC). CPSC recommends GFCIs where electrical equipment is near water, and describes portable ones for where an installed GFCI isn’t practical. Test it at least monthly and after a power failure, by its instructions or CPSC’s lamp check: plug in a lamp, press test (the lamp should go off), then reset (it should come back on). If it fails, tell facilities.
- Cords up. Mount the timer and power strip above tray level, and keep cords off the floor, away from spills and feet.
- Ask facilities first. Find out which outlets are GFCI-protected, whether extension cords and power strips are allowed, and whether a cart may stay plugged in overnight.
- Allergies. Offer nitrile rather than latex gloves, and have everyone wash hands after handling potting mix.
Weekends and breaks
- Lights. A plug-in timer can lose time in a power outage, so afterward, check its clock and test the GFCI (CPSC).
- Water. Bottom-water Friday, drain the excess, and check first thing Monday. Plan sowing so germination lands on school days.
- Temperature. UMN says to keep air above 60°F. Ask whether heat is turned down over breaks, and keep the cart away from cold windows.
- Long breaks. Send trays home with a volunteer, or time the project around the break.
Setup checklist
- Cart away from windows, by a facilities-approved GFCI outlet
- Tube fixture as long as the trays, on chains, 2 to 4 inches above the seedlings (LED: maker’s height)
- Grounded timer at 12 to 16 hours; heat mat on its own plug
- Watertight trays, with cords and power strip above them
- White surfaces on the back and sides
- Readings at center, ends and corners, turned into DLI (about 10 to 12)
- Thermometer, ruler and a data sheet (the teacher resources page has one)
- Monthly GFCI test and a plan for breaks
Sources
- Starting seeds indoorsUniversity of Minnesota Extension
- Important Considerations for Providing Supplemental Light to Indoor PlantsIowa State University Extension and Outreach
- Lighting Indoor Houseplants (G6515)University of Missouri Extension
- Measuring Daily Light Integral in a Greenhouse (HO-238-W)Purdue Extension
- From physics to fixtures to food: current and potential LED efficacyKusuma, Pattison and Bugbee, Horticulture Research 7:56 (2020)
- What Is a GFCI? (CPSC Fact Sheet, Pub. 099)U.S. Consumer Product Safety Commission
General information, not professional advice for a specific plant or crop. Spot something wrong? Email info@terrathink.io.


