ToolsCalculator
Fertilizer ppm calculator
Turn the three numbers on a fertilizer label into the concentration your plants get, or work back from a target ppm of nitrogen to how much fertilizer to weigh out.
The short answer For the ppm of any nutrient, multiply grams of fertilizer per liter of water by that nutrient’s percentage on the label, then by 10. In US units, multiply ounces per 100 gallons by the percentage, then by 0.75. So 0.75 g of a 20-10-20 in each liter of water gives 150 ppm nitrogen, a figure calculated from the recipe, not measured.
How to use it
How strong is my mix? takes the label analysis, the amount of fertilizer and the finished volume of the mix, and returns ppm of nitrogen, phosphorus and potassium. How much do I add? takes a target ppm of nitrogen and a volume, and returns the grams or ounces to weigh out.
Enter the analysis as the label’s three numbers, such as 20-10-20, then grams with liters, or ounces by weight with US gallons. For an injector, also enter its ratio, such as 1:100.
Weigh the fertilizer. UMass Extension says it should be measured by weight for mixing, not volume, and that a solution’s color is not a reliable gauge of its strength. If your label gives a spoon measure, weigh several level spoonfuls together and divide by the count, since many kitchen scales only read to the nearest gram, and keep that spoon for garden use.
What ppm means here
For fertilizer in water, ppm is milligrams of a nutrient per liter. One gram of fertilizer per liter at 1% of a nutrient is 10 mg of it per liter, or 10 ppm.
This is calculated from your recipe, not what an EC meter or ppm pen would read. A meter reads the whole solution, including whatever was already in your water, and a pen converts that conductivity to ppm on one of several scales (the EC to ppm converter explains them).
To check a mix, borrow UMass Extension’s injector check: measure the EC of your plain water and of the fertilizer solution, subtract the first from the second, and compare the difference with the maker’s EC chart, if there is one. EC and pH for plants explains the readings.
The formula
In metric units:
ppm = g/L × % × 10
- ppm: milligrams of the nutrient per liter of mix
- g/L: grams of fertilizer ÷ liters of water
- %: the nutrient’s number on the label (20 for the nitrogen in 20-10-20)
- 10: UMass Extension’s conversion constant for grams per liter
In US units:
ppm = oz per 100 gal × % × 0.75
- oz per 100 gal: ounces of fertilizer by weight × 100 ÷ US gallons of water
- 0.75: UMass’s constant of 75 for ounces per US gallon, ÷ 100, so 1 oz of any product in 100 gallons is about 75 ppm of that product
The calculator converts ounces and gallons exactly (1 oz per US gallon is about 7.49 g/L), so a US answer can differ from the 0.75 shortcut in the last digit.
Worked example (made-up numbers). 1.5 g of a 20-10-20 in 2 L of water is 1.5 ÷ 2 = 0.75 g/L:
- Nitrogen: 0.75 × 20 × 10 = 150 ppm N
- Phosphate: 0.75 × 10 × 10 = 75 ppm P2O5
- Potash: 0.75 × 20 × 10 = 150 ppm K2O
In US units (also made up), 0.5 oz in 5 gallons is 0.5 × 100 ÷ 5 = 10 oz per 100 gallons, and 10 × 20 × 0.75 = 150 ppm N.
Working backward, it rearranges the formula:
grams = target ppm × liters ÷ (% N × 10)
ounces = target ppm × gallons ÷ (% N × 75)
Here % N is the label’s first number. For 100 ppm N from a 20-10-20 (made-up numbers), 4 L takes 100 × 4 ÷ (20 × 10) = 2 g, and 5 gallons takes 100 × 5 ÷ (20 × 75) = 0.33 oz.
Phosphate and potash vs P and K
A label’s first number is elemental nitrogen, but the second and third are phosphorus and potassium in oxide form, P2O5 and K2O (UMass Extension). Virginia Cooperative Extension notes that fertilizer law generally sets which forms labels report. The calculator converts them:
P = P2O5 × 0.436
K = K2O × 0.830
P and K are the elemental amounts, and P2O5 and K2O are the label’s, in the same units. Virginia Cooperative Extension lists the factors as 0.4365 and 0.8301; UMass’s shortcut, dividing by 2.3 and 1.2, lands within half a percent.
In the example above, 75 ppm P2O5 × 0.436 = 32.7 ppm P, and 150 ppm K2O × 0.830 = 124.5 ppm K.
Injectors and stock solutions
An injector meters a concentrate, the stock solution, into flowing water. UMass Extension explains that 1:100 means 1 gallon of concentrate makes 100 gallons of final solution. It does not mean 100 ppm nitrogen. A 1% setting is 1:100, 2% is 1:50 and 0.5% is 1:200.
With a ratio entered, the calculator divides the stock’s ppm by the ratio’s second number (UMass’s dilution factor), or in How much do I add? mode multiplies the amount by it. As UMass notes, a 1:200 injector needs a stock twice as concentrated as a 1:100 for the same feed.
Worked example (made-up numbers). For 200 ppm N at the hose from a 20-10-20 through a 1:100 injector, the plants’ water needs 200 × 1 ÷ (20 × 10) = 1 g per liter, so the stock takes 1 × 100 = 100 g per liter. Checking forward: 100 × 20 × 10 = 20,000 ppm N in the stock, and 20,000 ÷ 100 = 200 ppm. In US units: 200 × 1 ÷ (20 × 75) × 100 = 13.3 oz per gallon of stock.
UMass also says to add the fertilizer first, then water to the mark (warm water works best), so the volume you enter is the finished stock. Injector ratios may change over time, so check yours periodically with the EC steps above.
How strong to mix
Published rates apply to particular plants and growing systems:
- Greenhouse crops: UMass Extension says 150 to 250 ppm N is often recommended for many floricultural crops on a constant feed basis (a dilute feed with every watering), and 200 ppm of N and K at each watering for plants in media with adequate phosphorus.
- Houseplants: UConn Extension gives no ppm figure. It says to follow the label and to feed during active growth, usually March until October, and generally not in winter. To feed more often, split the dose: a label rate of 1 teaspoon per quart monthly becomes a quarter teaspoon per quart weekly.
To see what your label rate means in ppm N, weigh the dose and enter it here.
UConn lists browning roots and leaf tips, wilting, poorly shaped leaves and a white crust on pot rims as possible signs of overfeeding, and says leaching with plenty of water often brings salts down. Why are my plant leaves turning yellow? sorts feeding problems from watering ones.
Safety and handling
- Follow the label. It overrides any number here, so never mix stronger than the label rate. As UConn puts it, “More is not better and excess nutrients can harm roots and leaves.” If the label calls for gloves or eye protection, wear them.
- Feed moist soil. UConn advises applying fertilizer to already moist potting soil to avoid root damage.
- Store it safely: in its original container, with no food or drink in the storage area (UMass), somewhere dry, away from pesticides and fuels, and locked up out of reach of children (UF/IFAS Extension).
- Label concentrates with the fertilizer formulation and concentration, as UMass advises for stock tanks, and never keep fertilizer in a food or drink container (UMass).
- Don’t pour leftovers down drains or toilets (UF/IFAS).
- Recheck the math. UMass warns that errors may be very costly. A stock solution is many times feed strength (100 times for a 1:100 injector), so never water plants with it undiluted, and double-check the ratio you enter.
Sources
- Fertilizer Calculations for Greenhouse CropsUMass Extension Greenhouse Crops and Floriculture Program
- Fertilizer Injectors for GreenhousesUMass Extension Greenhouse Crops and Floriculture Program (Smith)
- Conversion Factors Needed for Common Fertilizer CalculationsVirginia Cooperative Extension (Virginia Tech), SPES-201NP
- Fertilizing HouseplantsUConn Extension (Pettinelli)
- Fertilizer Storage and HandlingUMass Extension, Greenhouse Best Management Practices (BMP) Manual
- Spring Cleaning: Fertilizer and PesticidesUF/IFAS Extension Gardening Solutions
Estimates for general guidance, not professional advice for a specific plant or crop. Spot something wrong? Email info@terrathink.io.


